DIY Fluted Dresser
We have an awesome guest poster today, Kenna from @thefliphubb refinished this dated dresser into the cutest modern piece that is a real show stopper. Here's how she did it...
I’m bringing fluted back, YEAH. Them other dressers don’t know how to act, YEAH. (Do me a favor and please sing that to the tune of “I’m bringing sexy back” By Justin Timberlake okay, thanks.)
YOU. GUYS. I have been waiting and wanting to do this fluted look for so long, and decided it was time to bite the bullet and make the whole thing happen for my son’s room makeover (that let’s be honest — shouldn’t really be considered a makeover when the room was hardly made in the first place, ya know??).
It is much easier than it looks, and truly a doable DIY that I am so excited to be showing you!
Here is what you will need:
Half Round Moulding
Miter Saw
Wood Glue
Measuring Tape
Pencil
Paint
Take a look at this nasty before...
I started by measuring my drawer faces to determine how much material I would need. My drawer fronts were all about 10”, except for the top 8” drawer. Knowing this, I headed to Lowe's to get what I needed.
I ended up using 20 sticks for the whole thing. You could use less and combine scrap pieces together, but it was easier for me all around to just cut whole pieces. I would recommend this route.
After you have all of your material ready, its time to get out your miter saw.
Pro Tip here: create a saw stop. Super easy. I like to use a scrap piece of wood and a clamp- like this.
Simply measure how long each cut needs to be and set your stop accordingly. For example, if your wood needs to be 8” in length, you’ll set your stop 8 & 1/4” back from the blade — the 1/4 inch is to take into consideration the width of the blade.
I cut 4 about 4 pieces of half-round for each drawer. You can measure and divide by how many you will need, or you can cut what feels like a million, and go from there.
After you have cut enough wood for one drawer, its time to attach your wood! I used Krazy Glue wood glue to attach all of my pieces. Originally I was going to also nail them in using my finish nailer, but once I had them glued I realized that it would not be necessary to nail them. The glue is STRONG, and the half-round pieces weren’t going anywhere.
I simply put a line of the glue directly on the drawer face and then stuck the half-round to it. Matching each end up level with the drawer. Truly, this is such an easy DIY, it’s just so. time. consuming.
You’ll do this process of measuring, cutting, and gluing a few times, depending on how many drawer fronts you are covering.
After gluing all of my half rounds onto the drawer fronts, I let the glue + wood cure overnight. Also, it took me way longer than I thought and I was ready to be done for the day.
Now for the fun part! I don’t know about you, but nothing makes me happier than PAINTING. Especially when it’s a fun color. I decided to go with Sherwin Williams 2020 color of the year: Urban Bronze. It did NOT disappoint.
If you’ve been here longer than five minutes, you know I won’t shut up about my all time favorite paint additive BBFrösch. I mixed my BBFrösch into my satin Urban Bronze and then added it to my paint sprayer . I always thin down my paint with water when I use my sprayer, this helps with the flow of the paint and makes for a finer, smoother finish (if your paint comes out in blobs or spurts out chunks… thin it out more!).
I sprayed the dresser first and did the drawers next. I tried a few different methods of getting the most coverage with the bumps and angles that the half-round makes. The conclusion? straight on, direct flow is best! I thought going at an angle to hit the sides would be more efficient but alas, it wasn’t. Go figure.
After putting on the first coat, I let it dry overnight. Truly you only need to let it dry to the touch if you are using BBFrösch, but yet again it was time for me to call it a day. This project, being done continuously without interruption of changing diapers, school drop off, eating, and all of those semi-critical things, would take maybe a day + a day for cure time.
The second coat was done as the same, and with the BB Frösch plus the color being so dark, a third coat wasn’t needed. This ended up taking about half a quart of paint (think like $8 worth. Not bad, eh?). After my paint was all dry, I sanded things smooth with 220 grit and then touched up where it needed in a few spots just with my finger (I’m talking like pencil tip spots that needed help.
For bigger areas I would recommend your sprayer or brush so that the finish matches). Once the touch-ups were done, I sprayed my first coat of poly. I used a gloss finish, which is actually NOT the norm for me. I generally prefer a satin coat. However, I recently did gloss on a piano and loved the way it looked, not too shiny and definitely not dull, that I gave it a go for the dresser.
After the first coat of Poly, I sanded again with 220 grit once the poly had cured – the can call for an hour cure time in between coats depending on temperature/humidity levels, so be sure to check your can. Curing is CRUCIAL. I ended up doing 3 coats of poly and a final light sanding.
One issue I had was that a few of my half-round pieces ended up being slightly long, so when the dresser drawers were put back in, the wood hit the drawer below upon sliding in and scratched the paint (noooooo!!). My advice here is to learn from my mistake and be sure to sand the tops/bottoms of the wood half round to make sure they sit flush with the original drawer face to prevent any rubbing/scratching.
I let it cure for a day and then installed my knobs. This is a lot less daunting than it sounds AND actually easier with the half rounds because you don’t have to measure as much because you can base your spacing off of the number of wood pieces!
I wanted mine center on the face (Attach image of drawer w measuring tape + image with measuring tape across drawer front), and 1/4 of the way from each end.
I used my drill to pretrial holes, and then simply screwed the hardware in. My hardware is from hobby lobby, here is a similar style. You’ll want to use a smaller drill bit than screw so that it sits snug in the drawer. Nothing is worse than a hole too big for hardware.
And guess what? WE OUT. Mic DROP. All of those things.
What do you think? You’re going to try it out and tag me, right??
xo,
Kenna
